Meriam MFT 4010 Modular Calibrator_HART Communicator Manuel d'utilisateur Page 20
- Page / 114
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
15
Differential Pressure Calibration
Differential pressure gauges and transmitters can be calibrated using x
DN or xGI sensor modules. The
following drawing depicts a typical calibration set-up. The units under test should be isolated from the process
and drained of liquids if necessary. The low-pressure port of the DP unit under test is vented to atmosphere. Do
not connect the low-pressure port of an x
DN sensor to the low-pressure port of the DP unit under test. Such a
dead end connection can cause errors due to the expansion or contraction of trapped gas as a function of
temperature change.
Meriam does not recommend using process pressure as the pressure source for DP pressure device
calibration. Errors in measurement and calibration can easily creep in if the pressure source is unstable. In
addition, x
DN sensors have a maximum overpressure limit of 150 PSI when a three-valve equalizing manifold is
used properly. Sensor damage can occur if more than 15 PSI is applied to the high or low side of an xDN0020
or x
DN0200 sensor through improper use of the equalizing manifold.
Additional DP Application Information
In addition to reading gauge pressures, the MFT can also be used to measure
the pressure drop across a device in a pressurized pipe. Examples include
measuring the differential pressure across positive displacement meters, filters,
orifice plates or valves. Process compatibility and pressure ranges of the sensor
modules need to be considered for each application.
A three valve equalizing manifold or push-to-read equalizing valve should be
used to avoid damaging x
DN sensors. Follow the specific operating procedure
for each type of valve manifold.
3-Valve Manifold: Make sure all shut-off valves are closed. Connect to the
process. Slowly open the equalizing valve. Slowly open the high pressure
valve and then the low pressure valve. Close the equalizing valve and take
the measurement. Reverse the process to disconnect.
Push-to-read valve: Connect to the process. Open shut off valves. Push the
push-to-read plunger to take the reading.
- USER’S MANUAL 1
- ERIES USER’S MANUAL 2
- MPORTANT NOTICE 2
- SSISTANCE 2
- Single Function Keys 6
- Display Contrast 7
- Dual Function Keys 7
- Soft Keys 8
- Alphanumeric / Symbol Entry 8
- PV Prompt : Enabled 14
- Sensor Module Locations 16
- S1: Sensor Bay 1 (Left) 16
- S2: Sensor Bay 2 (Center) 16
- S3: Sensor Bay 3 (Right) 16
- MFT 4005 with HART 56
- MFT 4010 with HART 57
- Communications 57
- Rerange Menu 63
- Scaleable D/A Trim 70
- Revisions 73
- Back 76
- Control Doc) 85
- MFT ACCESSORIES LIST 86
- T/C open 87
- IV: 0.000 mA 87
- 3.0 User Re-Calibrate 89
- – Input offsets 90
- DAC offset constant 90
- IV: 4.000 mA 92
- 6.0 Approvals 96
- Option 2: RTD Measure Cable 102
- Ω Cal Res 103
- RIO Setup 104
- Ω Cal R 105
- Module Only Calibration 105
- Confirmation screen 105
- 4.0 Specifications 108
- 5.0 Accessories for RIO4000 108
- RIO4000 Accuracy Table 109
- Generic DOF (HART 5 devices) 111
- 3051C Rev. 2 Menu Tree 113
- EJA Rev. 2 Menu Tree 114
Produits connexes et manuels pour Capteurs Meriam MFT 4010 Modular Calibrator_HART Communicator
(40 pages)INSTEON 2420M manuals
Owner’s manuals and user’s guides for Motion detectors INSTEON 2420M.
We providing 1 pdf manuals INSTEON 2420M for download free by document types: User Manual
Commentaires sur ces manuels